Recommander à un ami


GPGS BOOT CLIP

GPGS BOOT CLIP

EUR 12.00
Prix régulier | Proposer un prix
Quantité:

Aperçu rapide


Poids: 15 gramms
Produit ajouté le 22.Oct.2013
Minimum order quantity: 1

Share

Use this S-Boot Repair Clip to repair the boot on Samsung i9500, i9300, i9308, i939d, m440s, i317, T889, E210k, E210L, E210s, N7100, N7108, N719, N7102 very easily without soldering.

GPG S-Boot Clip

  • With this GPGS-BOOT REPAIR clip its never been easier to repair the boot on Samsung OMAP chipset phones
  • Repair the boot on Samsung i9500, i9300, i9308, i939d, m440s, i317, T889, E210k, E210L, E210s, N7100, N7108, N719, N7102 very easily.
  • No disassembly is required except for a couple of models whereby you just need to remove the screen before doing the work.
  • No test point soldering is required.

 

Supported Models:
You can use this clip to repair the boot on the following phone models:

  • i9500 Boot Repair Clip
  • i9300 Boot Repair Clip
  • i9308 Boot Repair Clip
  • i939d Boot Repair Clip
  • m440s Boot Repair Clip
  • i317 Boot Repair Clip
  • T889 Boot Repair Clip
  • E210k Boot Repair Clip
  • E210L Boot Repair Clip
  • E210s Boot Repair Clip
  • N7100 Boot Repair Clip
  • N7108 Boot Repair Clip
  • N719 Boot Repair Clip
  • N7102 Boot Repair Clip

 

A Closer Look




USER FRIENDLY QUICK GUIDE

Below is a quick guide from one of our satisfied customers.
A Big thanks to Stuart Dew for the detailed images and user friendly guide to repairing the Samsung Galaxy S3 i9300.

Walkthrough for using this tool couldn't be easier!   I Have repaired 10 x  i9300 Galaxy S3 with this tool.
walkthrough for 9300

1. insert microsd card loom into phone
2. insert microusb into bottom of the phone
3. put battery into phone or connect bench psu (we have used a test battery so far with good results but for n7100 used a bench psu)
4. wait and have a cup of tea for 30 seconds to 5 minutes (quickest and longest times it took to finish)
5. phone will automatically go into download mode when it's finished!

We also found that you didn't need to flash all the phones again with new firmware just take battery out and restart as normal!
Brilliant product from GPG and excellent service from fonefunshop!

Here are some photographs I took during the repair process.

 

DETAILED INSTRUCTIONS

Samsung i9300 dead boot repair tutorial with GPG S-Boot Clip:

  • Power off phone.
  • Insert SD card connector from S-Boot cable into i9300
  • Connect power preferrably with regulated power supply or battery power supply, recommend to use of regulated power supply, because it can observe the change of electric current, when everything is ready.
  • Insert 19000 download clip.
  • Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
  • Generally after 2-5minutes, it will enter download mode.
  • If more than 5 minutes it has not entered download mode, then this usually means phone has flash ic problem or other hardware problems, please check the other reasons.
  • In the repair process, power current will jump every few seconds, which is telling you it is writeing data from SD to mobile phone.
  • Do not cut off power, otherwise it may never be able to repair again.

 

Samsung N7100 dead boot repair tutorial with GPG S-Boot Clip:

  • Remove the screen from the N7100 (if not removed, it will burn after repair)
  • Connect regulated power supply to N7100 pcb battery terminals
  • Insert SD card connector from S-Boot cable into N7100
  • Insert i9000 download clip
  • Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
  • If the flash is not completely broken, it will be repaired after 5minutes, and will enter download mode.
  • Plug the i9000 download clip and run flashing platform.
  • See if it recognizes the driver and port, if it does, then you can load file and flash, but remember to leave screen off until phone flashing is completed, or the screen will burn.

 

Samsung i9500 dead boot repair tutorial with GPG S-Boot Clip:

  • Remove the screen from the i9500 (if not removed, it will burn after repair)
  • Connect regulated power supply to i9500 pcb battery terminals
  • Insert SD card connector from S-Boot cable into i9500
  • Insert i9000 download clip
  • Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
  • If the flash is not completely broken, it will be repaired after 5minutes, and will enter download mode.
  • Plug the i9000 download clip and run flashing platform.
  • See if it recognizes the driver and port, if it does, then you can load file and flash, but remember to leave screen off until phone flashing is completed, or the screen will burn.
  • After flashing phone is in good state, just like you have changed the flash ic
  • If phone hangs after enter mode however, it means flash ic is totally damaged or other hardware problems and cannot be fixed.

Aucune spécification disponibles

No comments for this product!

Tous les champs sont obligatoires.

Tous les champs sont obligatoires.

Tous les champs sont obligatoires.

Reglez par Paypal